Equipment for metallurgy

Development and delivery of complex projects on the turnkey basis

Department of metallurgy at the company ENCE GmbH specializes in the development of complex processing lines and plants. The plants are completed with equipment from the world leading brands that are officially represented by ENCE GmbH in the CIS region. The units can be designed, completed and delivered turnkey on the prime contract basis; our technicians are also eager to carry out installation supervision, commissioning, as well as after-sales service of the following processing units and plants:

Cold and hot rolling mills

2-, 3-, 4- and 20-high stands of rolls are used for the rolling of billets, coiled steel, valves and bars.

Complete cold-rolling mills for coiled steel:
Strip gage: 0.3–4.0 mm
Coil weight: - max 30 t
Annual output: max 700.000 t

The equipment will be completed with the following items: electric and hydraulic drives, pinion stands, reduction gears, takeup and reel-off units, roller beds, chocks of backup and working rolls, bearing units, rolls made of special steel, dynamometers, thickness gages, automatic plants for coil marking (also applicable for hot-rolled coils), as well as auxiliary equipment for rolling quality control during the process and at the output.

The following equipment can also be supplied to the rolling plants: coil weighing and packing units, retrieving magnets and trolleys for metal transportation.

Tube-rolling mills

The following mills are offered for supply:

• piercing mills used for the piercing of billets with 80-270 mm gage and of ingots with o 350-600 mm
• Automills for the hot rolling of versatile pipes with o from 57 up to 426 mm
• Mills of continuous lengthwise rolling with two-high stands for the rolling of thin-walled pipes with o from 57 up to 114 mm
• Pilger mills for the production of thick-walled pipes with o from 57 up to 550 mm

• Three-high elongators (skew rolling) used for the production of high precision thick-walled pipes with o from 60 up to 180 mm. These elongators are mostly used for the production of bearing pipes (the production of rings for the ball and roller bearings)
• Reducing mills for the diameter reduction of the pipes that are received after the elongator processing by the method of lengthwise rolling, without mandrel, at the consequently located 2-, 3- or 4-high stands of rolls. The mills operate with an interstand tension, thus, not only pump diameter, but also wall gage can be changed. Pipes with o from 25 up to 76 mm are rolled on the reducing mills

In addition to the above mentioned pipe-rolling plants (piercing mills, elongators, reducing/extending mills), the following items can be supplied:

• Heating furnaces
• Reeling and sizing mills
• Straightening machines
• pipe-cutting and pipe-threading machines

as well as other equipment required for the specified working operations.

Pipe electric-welding machines

The process of welded pipes production consists of the following main operations: the billet is formed, the edges of the billet are welded and after that the pipe diameter is reduced.

We also offer such equipment as:

• Continuous tube-forming mills used for billets forming during the manufacturing of tubes with o from 8 up to 530 mm out of coiled metal as well as out of specific cut length sheet. Billets for two-seamed pipes with diameter up to 1010 mm can also be produced on these forming mills
• Continuous hot molding equipment at driven running rolls at the pipe furnace pressure welding units
• Mechanical and hydraulic presses for billet forming out of specific cut length sheet during the manufacture of large-diameter pipes (exceeding 426 mm). The forming can be carried out either with several procedures on one press, or on 2 or 3 presses with each carrying out certain operations. The process ensures high quality of forming
• Forming machines of rolling mandrel-type and sleeve-type. Spiral forming is used for the pipes with diameter from 76 up to 1420 mm, it is more appropriate for large-diameter pipes (exceeding 426 mm)
• Pipe electric-welding machines with arc welding under the layer of flux [mostly for large-diameter pipes production, o from 426 up to 1420 mm] and with arc welding the inert gas (argon, helium) arc protection (for the production of pipes from corrosion-resistant and other high-alloy steels)
• Reduction mills for welded pipes with o less than 76 mm
• Complete processing lines designed for welded pipes production, transportation, hot and cold finishing, storing, packing, etc. In addition to forming, welding and reduction mills, such equipment as strip preparation machines, saws, cutting machines, straightening machines, pipe-cutting and pipe-threading machines are also included in the line

Press-forging plants

Range of products offered:		Brief description
Forging machine with 4 hammers for section steel production		Compacting force range: from 2,5 MN up to 20 MN hydraulically actuated and with fully automatic process control
Open die forging mill		Our program includes all the open die forging machines, presses and manipulators with modern actuators and program control for both automatic and programmable operating modes in the range of 5-150 MN
Forging manipulators		Carrying capacity up to 125 tons
Press-forging plants		Forging presses designed for special purposes, have a stable construction with stepless adjustable hydraulic drive for precise forging of titanium, aluminum and superalloys
Special presses		Piercing, pipe and profile, bending, straightening and universal
Hydraulic drives		Oil or water – direct or accumulator drive

The following equipment that we offer is currently used:

Press-forging plant 15MN
Customer: MIDHANI - Hydarabad, India

• Press model: 15 MN
• Two 10-ton forging manipulators
• Blank supply trolley
• A rotary table
• Main pumps: 6 pcs. RX 250
• Oil volume: 20000 liters

Press-forging plant 55MN
Customer: BUDERUS, Germany

• Press weight: 900 tons
• Height: 10500 mm
• Depth: 3500 mm
• Main pumps: 12 pcs. RX 500
• Oil volume: 45000 liters
• Power: 5600 kilowatt

Press-forging plant 90MN
Customer: TONGDI, China

• Press weight: 1300 tons
• Main pumps: 8 pcs. RX 500
• Oil volume: 55000 liters
• Power: 5000 kilowatt
• A DDS-manipulator 80tons/160tons

In addition to equipment supply our company (in cooperation with its German partner Wepuko Hydraulik) is eager to design, reconstruct and update an existing plant in order to increase its efficiency and to reduce energy consumption as well as noise level of processing plants and units.

Instrumentation systems for rolling mills

   

Non-contact systems of measuring complex profiles of products made from steel and other materials in real time mode.

Application: Laser systems are used for measuring profile sizes, fault detection and detection of form deviations from hot-rolled products in a mill line in extremely difficult conditions (possibility of profile measurement in hot conditions at temperature from 900°C to +1200°C, in cold conditions at T from - 0°C to +60°C).

Surface fault detection automatic systems

Application: the system allows to detect surface faults even in difficult hot rolling mill conditions through smoke, steam, water, dross.

You can find more information about instrumentation systems offered under: www.ence-gmbh.ru

Roll grinding equipment

Fully automatic NC roll grinding plants designed for operating in heavy, medium and light modes. The plant allows to keep the tolerances and to provide a high-quality degree of finish. They are highly reliable and supplied with modern control equipment.

Technical characteristics

• Diameters of rolls to be processed up to 700 mm
• Machine length from 3000 up to 10000 mm
• Weight of rolls to be processed up to 4500 kg
• Rolls rotating speed is adjustable through the inverter
• Servo drive
• Belt sanders 7,5 kilowatt and 11 kilowatt for more material removal
• Pneumatic belt tension
• Belt size 150 x 2500 mm
• Optional: steel cutter holder
• Optional: grinding machine for the edges of printing rollers
• Optional: automatic diameter measurement
• NC control panel
• Software for movement/axes correction and
• Grinding with lubricoolant and filter system
• Dry grinding with dust removal
• There are open construction/fully enclosed machines
• Special anticorrosion complete equipment
• Optional: automatic crane loading
• Optional: process control system software

Horizontal Spindle Surface Grinder with Rectangular Table

Application: grinding of workpiece flat surfaces under various manufacture conditions.

Design features:

• Backlash-free wheelhead movement due to machine rolling screw – nut pair at vertical wheelhead travel.
• The machines are equipped with an automatic lubrication system and abrasive dust protection.

Technical characteristics:

Workpiece dimensions, mm:	max. 2000 x 630 x 630
Gripping plate working surface dimensions, mm:	2000 x 630
Table longitudinal travel, m/min:	3...30
Grinding wheel diameter, mm:	500 - 600
Wheelhead vertical movement graduation per one dial, mm:	0,004
Automatic vertical wheelhead feed, mm:	0,004...0,1
Wheelhead spindle speed, rpm:	1500
Main drive power, kW:	30-35
Overall dimensions, mm:	5950 x 2880 x 2880
Weight, kg:	15000

Trolley Motor Trucks

Application: intrashop transportation of various freights on rectilinear horizontal sections of railway.

Truck electric power is supplied by means of trolley and loop (cable) current distributor.

Technical characteristics:

Load-carrying capacity, t:	from 80 to 160
Travel speed, m/s:	0,45
Track centers, mm:	1524
Truck base, mm:	2800/1000 or 4000/1000
Axle number, pcs.:	2 or 4
Platform dimensions, mm:
Length:	7000
Width:	2500
Platform height above rail elevation, mm:	1285 or 1370
Electric motor power, kW:	2x7,5
Weight, kg:	from 15900 to 27340

As an option trucks can be manufactured to be with a cable drum and explosion proof.

Shot blasting machines

The company offers automatic machines for mill rollers shot blasting used for peening, roller drum surface hardening, to gain surface roughness of 1,5-3,5 mcm (peak density per 1 mm, 30 – 80)

Technical parameters of the machine:
Compressed air consumption - 2290 l/min
Nozzle size - 6,4 mm, tungsten carbide
Shot peen cycle – up to 2 hours of continuous operation
Recommended abrasives – cast iron grit, GH grade

Steel strip pickling line

We offer push-pull pickling lines for hot rolled carbon steel acc. to EN10051

General characteristics of pickling lines we supply:

Annual capacity – up to 600 thousand tones in a year
Strip thickness – 1,0-4,0 mm
Strip width – 900-1550 mm
Coil inner diameter - 750 mm
Coil outer diameter – max 2200 mm
Coil weight – up to 30 t
Line speed – max 150 m/min
HCL concentration at the last stage of washing – max 60 mg/l

Scope of supply of our pickling lines includes also equipment (assemblies) for removal of copper ions from the pickling liquor (solution of the problem of "copper film" on the surface of pickled rolled steel).

Pickling line consists of:

• Entrance department: coil rack, loading carriage, decoiler, dressing machine, horizontal and diagonal cutters

• Process department: Pickle bath consists of four sections operating in a cascade mode. Each pickling section includes circulation loop with a circulation tank, a pump, heat exchangers, back line from the pickling section. Leaving the pickle bath the strip is squeezed by two sets of squeeze rollers. Washing bath is installed right after the pickling bath, which has two stages and operates in a cascade mode, by backflow to the strip motion. Squeeze rollers are installed between each washing section in order to minimize the water transfer from one section into another. Strip travel in the pickling and washing sections is done by drive transport and squeeze rollers. The pickle bath, washing and storage tanks are connected to the exhaust system. The exhaust system is equipped with a scrubber and two droplet separators to purify exhaust fumes. A strip dryer with edge cooling unit is provided after washing.

• Exit section: The strip goes to the next feeding device located in front of a looper after the dryer. The looper pit serves as a material accumulator in case of shutdown or at various strip speeds in separate line sections. A feeding device with a mechanical side guide is installed behind the looper pit. The front strip end goes to edge trimming shears equipped with swivel heads. Scraps are cut into pieces by a scrap cutter. A three-roll backward tension mill follows next; an inspection stand is situated behind it. An electrostatic oiler is provided for strip oiling, after that the front strip end is supplied to a tension reel. The tension reel is equipped with a control system, which makes winding with uniform edges possible. Coils are removed from the tension reel by overhead travelling cranes and placed on a saddle.

Automatic Chamber Filter Presses KMP

Fully automatic chamber filter presses KMP are designed for filtration of suspensions containing from 10 to 1500 kg/m³ suspended particles and forming deposits with high liquid resistance.

KMP filter press has new engineering design features:

• Hydraulic plate clamp mechanism;
• Automatic control system;
• Filter cloth tensioning device.

Filter presses are used to filter industrial wastes in electroplating, pickling and other industries at the final stage of sludge dewatering after thickening and reactant treatment.

KMP type filter presses can use filter fabrics with mechanical warp-wise tearing strength of min 285 kg.

Legend:

• K – horizontal plate chamber filter press
• M – with mechanical pressing
• P – cake removal via moving cloth
• 25 – filter surface area, m²
• 1 – unpressurized with general purpose electric equipment
• K – corrosion resistant steel
• 1 – stainless steel

Example: KMP 25-1K-1
Manufacture and supply of any design is according to DIN.

Technical Data

Type	KMP 2,5	KMP 5	KMP 10**	KMP 12,5	KMP 22**	KMP 25
Filter surface area, m2	2,5	5	10	12,5	22	25
Chamber volume, m2	0,11	0,22	0,51	0,55	1,19	1,1
Pressure, MPa (kgf/cm2):
operating (suspension, washing liquid, air, water, at membrane pressing), max	1,6 (16)	1,6 (16)	1,6 (16)	1,6 (16)	1,6 (16)	1,6 (16)
of filter press cloth washing, max	0,3 (3)	0,3 (3)	0,3 (3)	0,3 (3)	0,3 (3)	0,3 (3)
of oil at hydraulic control system	2 (20)	2 (20)	2 (20)	2 (20)	2 (20)	2 (20)
of oil at hydraulic clamping system, max	15 (150)	15 (150)	15 (150)	15 (150)	15 (150)	15 (150)
Filtrated medium temperature, K (°C)	278-353 (5-80)	278-353 (5-80)	278-353 (5-80)	278-353 (5-80)	278-353 (5-80)	278-353 (5-80)
The highest cake thickness, mm	35	35	45	35	45	35
Max. admissible load by wet cake, kg/m2x h	110	110	110	110	110	110
Installed capacity, kW, max	28,3	28,3	28,3	28,3	28,3	28,3
Power consumption, kW, max	24	24	24	24	24	24
Electric power supply with dead-earthed neutral:
voltage, V	380	380	380	380	380	380
frequency, Hz	3-50	3-50	3-50	3-50	3-50	3-50
Overall dimensions
length, mm	2910	2910	3980	3980	3980	3980
width, mm	1950	1950	2350	2350	2350	2350
height, mm	2550	3300	3100	3100	4200	4200
weight*, kg	5750	6930	11700	11200	15000	15250

Notes:
* For filter presses manufactured of carbon steel
** Filter presses for easily filtrated suspensions

KMP Filter Press Technical Description

Filter press KMP comprises set of horizontally positioned filtering plates, placed between the thrust and pressure plates. Hydraulic clamping unit with wedge fixation performing lifting, sealing and lowering of plates pack is mounted on the supporting plate. Thrust and pressure plates are connected with tie-columns. Continuous filtering belt (cloth) is pulled zig-zag-like between the filtering plates. Cloth shifting drive containing driving and pressing rollers conducts filtering cloth shifting for cake discharge and its recovery. Driving roller receives rotation from the electric motor via V-belt and reducer. Washing tubes for cloth washing and blades (knives) for its cleaning are installed inside the recovery chamber. Cloth is tightened by tightening unit fixed on cloth shifting drive and thrust plate. Chains and cloth tightening unit fastened on them receive their motion from hydromotor. Cloth adjustment roller serves for eliminating of filtering cloth side-shifting in relation to filtering plates.

Supporting plate, tray, washing chamber and cloth shifting drive are installed on the same frame. Manifold for water supply to the membranes is mounted on one of the tie-columns.

Filter plates consist of two parts: upper – the body (filtrate chamber) and lower – the frame (filtration chamber)..

Body serves for filtrate collecting and discharge and has the bottom, side walls and drainage base in the form of separate inserts. Frame serves as the filtration chamber, in which the cake is accumulated and dried. Rubber membrane for cake pressing is placed between the body and the frame. Clamping unit presses together plates pack and makes filtering chambers air-tight. When plates are pressed together suspension under pressure is fed to the lower part of each plate- filtering chamber. Liquid phase passes through the cloth, drainage base and is discharged out of the filter via discharge manifold. Solid phase caught by the cloth, is preliminarily pressed and, if it is required by the technology, is washed. Washing liquid is fed into the chambers via supply manifold, while washing filtrate is discharged from the filter via discharge manifold.

After washing cake is pressed again by rubber membranes, dried by pressed air and discharged when the filter press opens. Plates are suspended on the special links, cloth shifting drive gets energized, and cake is carried on the cloth from the inter-plate space and dropped to chutes-hoppers on both sides of the filter. Cloth is pulled through the washing chamber, washed, then filter is clamped again, and the operation cycle starts again. Operations duration and sequence is determined experimentally or upon the results of filter press operation with the similar suspension.

KMP filter presses have three material options of medium-contact parts: carbon steel for neutral and alkali suspension filtration; corrosion-resistant steels – for aggressive suspension filtration; Titanium alloy BT 1-0 – for aggressive suspension filtration. KMP filter presses are supplied complete with general purpose or explosion-proof electric equipment of the rating which is not below B3T3 with control system based on electric relays or pneumatic elements (for BI-a and ВII-a premises classes) and microprocessor-based control systems.

Possibility of quick readjustment, reduction of technological time, high capacity, conventional and microprocessor-based automatic control systems, reliable safety precautions, reliable service maintenance guarantee optimal use of KMP filter presses and make them indispensable for many branches of industry, including: coal, mining, metallurgical, engineering and power engineering fields.

Steel Strip Hot Galvanizing Line

Complex hot galvanizing lines of the cold-rolled steel strip have the annual output ranging from 60 to 500 ths. tons per year.

Technical characteristics of the supplied hot galvanizing lines:

Strip thickness – 0.3-2.0 mm
Strip width – 600-1650 mm
Coil weight – up to 30 tons
Coil external diameter – up to 2100 mm
Line speed – up to 180 m/min

You can find more detailed information on similar equipment on our website: www.galvanazing-line.ru

In addition we supply units and parts of hot galvanizing line dipping equipment, which are made of stellite, ceramics, 316L stainless steel and other steel:

• sink drums (rolls)
• correction rolls, stabilizing rolls
• journal bearings (stellite, ceramics)
• bushings (stellite, combination)
• various configurations and designs of washers
• tempering mill rolls
• furnace rolls, including those with ceramic coating

Detailed information is located on our website:www.stellite-parts.ru

Hot Galvanizing Lines for Reinforcement Rods, Metal Structures and Railings

We can supply complete lines for hot galvanizing of steel structures with the annual output ranging from 10 ths. to 100 ths. tons.

You can find more detailed information on similar equipment on our website: www.galvanazing-line.ru

Steel Strip Color Coating Lines

Complex steel strip color coating lines feature the following basic characteristics:

Incoming material – galvanized strip
Strip thickness - 0,2-2.0 mm
Strip width - 600-1500 mm
Coil weight – up to 10 tons
Process speed – up to 200 m/min
Coating types – polyester, epoxy, acrylic, PVC and others.

Detailed description of the technological process and equipment list are on our website: www.coaters.ru

Thermal and heating furnaces

In 2010 ENCE GmbH and BTF Technofour (Belgium) concluded a partnership and cooperation agreement on design and production of various heating and thermal furnaces as well as on reconstruction (up-grading) of existing furnaces directly at production site (to increase the efficiency and automation level and reduce gas flow rate).

Rotary furnace (revolving furnace)

The company specializes on packaged supply of various thermal and heating furnaces on the turn-key basis for different industrial applications (roller-hearth, muffle, pusher-type, induction, walking beam, circular, bell-type, through and other types of furnaces), providing non-standard technical solutions integrated in the process lines. The operating temperatures range of the mentioned furnaces reaches 1800°C. Depending on the customer’s process requirements the furnaces can be designed for operation in oxygen, in neutral atmosphere, in vacuum, as well as for special heat treatment such as cementation or nitride hardening.

vacuum furnace	high-temperature forced-convection furnace with automatic sliding doors	vertical furnace for heat-resistance materials testing
travelling hearth furnace with operating temperature up to 1400°C	bell type furnace for thermal heat treatment in shielding atmosphere	furnace, equipped with roller conveyor and vertical gate

You can find more details on heating furnaces reconstruction on our specialized website: www.energy-saving.uz

Refractory Lining for Ferrous Metallurgy

ENCE GmbH offers a package of measures dedicated to lining maintenance and reconstruction as well as first time lining of ferrous metallurgy technological equipment. The company specialists will make all the required estimation and best selection of refractories, engineering, installation supervision, technical support and service maintenance.

ENCE GmbH offers advanced ferrous metallurgy materials according to all the demands made for products of this sort in EC. We offer refractory materials for converter industry and electric furnace steel making, products for ladle metallurgy, refractories for continuous steel casting and deairing equipment.

Converter industry. Refractory line offered by ENCE GmbH includes products for: throat opening, discharge zone, belt assembly, charging zone, bottom and bath, vent units, backup lining, repair mixtures.

Please, see more details of the offered lining at the page refractory lining for ferrous metallurgy.

Slitting-and-Shearing Lines, Combination Lines

Technical data of automatic slitting-and-shearing line for coiled steel and non-ferrous metals:

• Band width – 500-1600 mm
• Band thickness - 0,3-4,0 mm
• Coil weight – up to 20 tons
• Band feed speed– up to 100 m/min

The slitting-and-shearing line for metal consists of:

• decoiler
• cutting-straightening machine
• piler
• roll table
• guiding unit
• coil winder
• coil removal trolley
• hydro-pneumatic system drive
• Control panel. Two operators are required for shearing line maintenance

More information www.metall-cutting.ru

Equipment for metalwork

Sheet metal bending equipment

Application: bending of sheet steel up to 1 mm thick and 3000 mm long.

Design version:

• electromechanical
• hydraulic
• electromechanical, extended length

Here you can find more information about the supplied equipment

Road fencing profiling machine lines

Application: road fence production

Basic machine line operations: unreeling, alignment, perforation, profiling, cutting.

The profiling machine lines use CNC system based on PLC and frequency speed regulation. The lines are fully automatic.

For more information please visit www.metalworking-equipment.ru

Automatic lines for metal tile production

During the sheet shaping the desired (set) length is cut off automatically according to the buyer's request

Distinctive aspects of the supplied lines:

• High operation speed
• Reliability
• Low noise level
• Robust transmission
• Easy operation
• Specially designed for working with cold-rolled steel

For more info please visit www.metalworking-equipment.ru

Profile forming machine lines

The following equipment can be supplied:

• Ridge cap rolling machines
• Trapezoidal profile forming machines
• Roof and facing profile forming machines
• Slate panel machines
• Metal siding production lines
• Sandwich panel production lines

HERE you can find more information about the basic and additional equipment of the profile forming machine lines.

Water falling pipe forming machines and pipe elbow machines

Water falling pipe diameter: 87 mm, 100 mm and 125 mm

Part blank

• Steel 0,40 - 0,50 mm
• Aluminum 0,57 - 0,81 mm
• Copper 16 oz

Skelp width
292-416 mm ±2 mm

Efficiency
20 m/min or 350 elbows per hour

More information

Flange beam processing and welding lines

The following equipment can be supplied:

• Flange beam gravity position welding line
• High efficient automatic lines
• Horizontal welding lines
• Flange beam processing lines
• Flange beam 3-D drilling machines
• Band saws
• Formed part plasma arc cutting units with perforation function.

The detailed characteristics of the supplied equipment can be found HERE

Auxiliary equipment for metallurgic shops

Wepuko high-tech high-pressure pump systems

• High pressure hydraulic systems designed for pressurization in technology processes
• Scale removal systems
• Water hydraulic systems
• Press drives
• pump units for slag cooling and washing-out in rolling mills with deburring station
• Special high pressure pumps (1500 bar) for lubrication of hydrostatic bearings in cold and hot rolling mills
• pump systems for serial part deburring by pressures up to 1000 bar

More information

Corrosion-resistant centrifugal pumps Apollo-Göβnitz GmbH (Germany)

Corrosion-resistant centrifugal pumps of different types and designs, with capacity up to 8000 m³/h and operating pressure up to 160 bar:

• Volute type pumps
• Multistage pumps up to 160 bar
• Vertical pumps
• Self-priming pump

• Pumps for liquid mediums with solids
• Axial flow pumps
• Canned motor pumps with magnetic coupling

More information about the company products: www.apollo-pumpen.ru or www.chemical-pumps.uz

WOMA high pressure pumps (Germany)

High and ultrahigh pressure units for:

• High pressure water-jet equipment
• High pressure transportation equipment
• Cleaning aggregates for industrial equipment: heat-exchangers, pipes, clinker furnaces, etc.
• Units of fireless cutting of pipes and non-metallic sheet material

Operation pressure up to 3500 bar
Capacity up to 3070 l/min
additional information

Shut-off and control valves, safety and check valves

The company is willing to supply the following shut-off valves to order:

Shut-off valves Check valves Wedge-gate valves Valve gates Plug valves Return valves Ball valves Safety valves Check valves Choke valves Butterfly gates

Technical data of supplied valves:

PN 5 – 500 bar
DN 25 – 1500

Construction material:

• Stainless steel 304, 316 321, etc.
• Special steel and alloys (hastelloy, titanium, etc.)
• Carbone steel
• Bronze

For more information about the valves please visit: www.valves.uz

Electrical equipment

ENCE GmbH can supply uninterruptive power supplies, current converters, frequency inverters and current rectifiers of different capacity.

All the offered equipment is produced according to ISO 9001. Remote control and monitor is possible.

For more information about the offered equipment please visit www.ence-ups.ru